Build a DIY mobile workbench that fits both your table saw and miter saw with these plans.
This post may contain affiliate links. If you make a purchase from one of the links, I may make a small commission at NO EXTRA COST to you. This helps keep the tutorials and plans free here at Bitterroot DIY. Thank you for your support! See my full disclosure here.
You all loved the DIY Mobile Workbench with Table Saw so much that I brought it back for round #2! I teamed up with my friend Ashley from Shes the Carpenter over on Instagram for this NEW & IMPROVED mobile workbench with BOTH a table saw and miter saw. If you don’t already, make sure to go follow Ashley for TONS of amazing DIY projects! She built this beast of a workbench and is always sharing great woodworking tips and tricks!
There are two variations of plans – one for a RIGID table saw (pictured) and the other for a RYOBI table saw.
I featured the dimensions for the RIGID table saw in the post below, but you can adjust the table saw shelf to fit any table saw. The only thing you have to change is the size of the shelf and location of the support leg that the shelf attaches to.
Enjoy the plans!
**If you find any errors in the plans, please let me know and I’ll update them accordingly. I do my best to get everything correct, but it’s just me back here behind the screen checking my own work.
The lumber and cut lists are available for purchase. Your purchase also includes a downloadable PDF of the plans. If you prefer, the plans are available for free in the post below – you simply have to calculate the lumber and cut lists yourself. There are plans available to fit a RYOBI table saw, as well as a RIGID table saw. If you own a different table saw, you can just adjust the shelf to fit.
Assemble the bottom frame according to the diagram. Use 2 1/2″ self tapping screws through the frame to attach the 2x4s. Pocket holes are a great option if you don’t want to see the screws from the front of the bench. However, since this is just a workbench, I simply screwed through the frame into the shorter 2x4s.
Attach the side legs to the bottom frame with 2 1/2″ screws. The bottom of the frame should sit flush with the bottom of the legs.
Attach the front and back legs to the frame and side legs with 2 1/2″ screws. I attached the legs to the frame first and then drove a couple screws through the legs into the narrow side of the front and back legs to secure them together. You can see the approximate location of the screws in the diagram above.
The diagram only shows dimensions on the front legs. The back legs exactly mirror it.
Here’s a top view of how the legs go together:
Put the bottom shelf in place on the bottom frame and attach with 1 1/4″ screws. Countersink the screws so they won’t get in the way. It’s very difficult to put the bottom shelf in later, so definitely put it in before attaching the top frame in Step 5.
Build the top frame in place as shown. Use 2 1/2″ screws to attach the frame to the legs.
Here’s a different view from the front to show you what it looks like at this point:
Attach the 2×4 feet to the legs with 2 1/2″ screws. Fasten the locking casters to the feet with 1 1/4″ screws. I used washers on each screw since the screw heads were smaller than the holes in the caster wheels. You could also use washer head screws.
Assemble the frame for the table saw shelf with 2 1/2″ screws. Place those two center 2×4 supports wherever necessary to support the base of your table saw.
You could also add particle board on top of the 2×4 frame to set the table saw on. Just make sure to leave room in the bottom for dust collection (or at least for the sawdust to fall out).
Place the shelf at the appropriate height for your table saw and attach to the workbench frame with 2 1/2″ screws. Use clamps to hold the shelf in place while you attach it to the frame.
Measure the height of your miter saw’s tabletop. A good way to do this is to set your saw on a flat surface, lay a board across the saw so it extends off the edge, and measure from the flat surface to the bottom of the board.
Position the 2×4 miter saw shelf supports at the appropriate height so the top of the miter saw will sit flush with the tabletop when it’s on the shelf.
Attach the 2×4 miter saw shelf supports to the inside of the midSlide the miter saw shelf particleboard into place on top of the 2x4s you just attached.dle legs. Drive two 2 1/2″ screws on each side into the legs.
Slide the miter saw shelf particleboard into place on top of the 2x4s you just attached.
Attach a stop block on each side behind the miter saw shelf to prevent the shelf from sliding backward under the bench.
You can just use an extra piece of 2×4 cut to fit and attach it to the 2×3 and 2×4 shelf support.
Center the tabletop and attach it to the frame with 1 1/4″ screws. There should be a 2″ overhang on the sides of the table top and it should be flush with the outside edge of the legs along front and back. Countersink the screws into the particle board so they won’t get in the way of your work.
Since the miter saw shelf is just held in place by the stop blocks you attached in Step 11, you can use that same piece of particle board (or plywood) to fill in the tabletop when you need the full workbench.
Place the miter saw shelf in the shelf slot when you want to use the saw:
Move the shelf up to the top of the workbench when you need a full out-feed table:
**Optional: Add a small clamp rack along the end of the workbench once it’s finished. On the first DIY mobile workbench, I just used a small scrap board and screwed it to the inside of the legs.
Ashley added the clamp rack in a little different spot, so feel free to do whatever works best for your shop.
She also added a small nightstand along the far side of the workbench for some extra drawer storage, which is such a great use of space:
And just for good measure, here are a few more photos to show how that miter saw shelf works:
Good luck, happy building, and don’t forget to tag me @bitterrootdiy and Ashley @shesthecarpenter over on Instagram if you build this ULTIMATE DIY Mobile Workbench! We’d love to see it! You can also send me photos at bitterroot.diy[email protected]
Please let me know if you have any questions and I’ll get back to you as soon as possible.
Thanks for stopping by!